Sunday, January 3, 2021

Crushed like a Bug

I write this blog not to draw attention to my own stupidity, which is usually way to easily done without trying, but hopefully to help someone else avoid making a similar mistake.

Sometimes we get so complacent in the things we do everyday that we get careless.  I recently purchased a set of palate forks for my skid steer.  I tried to move a piece of steel pipe about 8" in diameter and 12' long.  I pushed one of the forks into the end and lifted, observing immediately that it was heavier than expected.  Evidently the pipe was full of dirt.  Things were going well until I hit a bump, which caused the pipe to bounce.  The increased weight put extra strain on the fork and bent the back plate which connects it to the skid steer.

I tried bending the back plate to its proper position by pushing the fork in the opposite direction against solid objects, like a large tree, but it didn't work. The plate is quarter inch steel and pretty rigid.  I tried a few other things that didn't work and finally decided that the best option was to put a wedge between the back plate and the place it connects to the skid steer and use the unit's hydraulics to squeeze it back into place. 

In order to do this I had to cheat the unit's safety system, something that I really know is kind of stupid.  They put such systems in place to protect stupid people from damaging themselves.  I did it anyway.  The seat switch that turns the machine off if you get up off the seat went bad a long time ago so I had by-passed it.  I started the machine and raised the safety bar and got out with the engine running.  I lowered the safety bar and pushed the button that activates the hydraulics so I could operate them from outside the cab.  Safety system effectively by-passed.

So, outside the machine I put a block of wood between the bent back plate and the plate it connects to.  Holding the block in place with my right hand I proceeded to reach inside the machine and operate the hydraulics with my left hand, which is the opposite hand normally used for that purpose.  As you can see I was build a recipe for disaster.  I activated the hydraulics a couple of times, not having the desired effect to bend the plate back into shape, but somehow the block of wood slipped. Because I was operating the controls left handed my reaction time was slow and my right hand got squeezed between the plates where the block of wood had been.

I'm sure I have not experienced a lot of pain in my life, but I don't remember ever experiencing pain like I felt having my hand crushed between those two steel plates.  There are a lot of nerve endings in the hands and fingers, and everyone of them was screaming in my right hand.  I think I almost passed out from the initial wave of pain, but maintained enough presence to reverse the hydraulics and release my hand from the machine's death grip.  For a few moments I thought every bone in my hand was broken.  The intense pain throbbed mercilessly for a few minutes, then slowly subsided to the point I could cuss. Amazingly, I didn't use any bad words, and mostly berated myself for doing something so obviously dangerous.

Luckily, it was a chilly day and I was wearing a winter glove with heavy lining which I believe, along with divine intervention, helped prevent more serious injury.  After letting the pain subsided to a manageable level, with my hand hanging at my side I put the skid steer away and went to the house.
When I removed the glove I discovered that the skin had not been broken and there was no external bleeding, but the hand was becoming scarlet and swollen. Within a few hours my hand looked like it belonged to Mickey Mouse.



Wrapping this up, I had an x-ray taken a few days later and the PA that treated me said I was really lucky because there were no broken bones.  That was hard to believe, but steeling myself against the pain I could move all my fingers and all the joints worked. It took about six weeks before I had much use of the hand, and I got fairly good at doing things with my left.  It has now been about four months and it is mostly recovered.  There is still some pain in the joints of my fingers, especially first thing in the morning, and some in my wrist when I bend it in certain positions.  My little finger still won't bend all the way, but hopefully with time and therapy it will return to normal.  I also don't have full strength in my grip or in the use of the wrist, but that is slowly improving.

So, in summary, I made a stupid mistake and I paid for it.  I have always thought of myself as one who can foresee trouble and accidents and therefore avoid them, but even so by getting a little too comfortable and complacent I failed to prevent this one.  Obviously even obsessive-compulsive behavior can't prevent all accidents, and I wouldn't want to go through life keeping myself in a protective bubble, but I have made a promise to myself to be more careful and to try to avoid getting so comfortable in every day activities that caution flees.
 

Tuesday, November 27, 2018

Kolob Canyon Time-lapse Video

I got a new camera a while back that has time-lapse video capability.  I experimented with it and got some interesting stuff that I want to share.  This video was taken from our front porch on November 3, 2017.  The camera was set to take one frame every 10 seconds for about three hours.




Monday, November 26, 2018

Making Wooden Bowls

I got a wood lathe in January this year (2018).  As mentioned in a previous post I got it primarily to turn a pedestal for a table I was making.  Before the table was finished I started making other things.  I started with fish bonkers, a mini baseball bat used to put a fish out of it's misery and keep it from flopping around.  I made several out of some red cedar that grows nearby and smells wonderful.

Red Cedar Fish Bonker
My next project was a bud vase.  I made it for my sweetheart for Valentines Day out of black walnut.

Black Walnut Bud Vase
I made a pair of table lamps also from black walnut.  One is shown as they are nearly identical.

Black Walnut Table Lamp
Goblets are quite easy to make and your imagination can run wild.

Black Walnut Goblet

A friend wanted an urn for his father's ashes.  

Black Walnut Urn
My first bowl.

Pinion Pine Bowl with urethane finish
I got the idea on You Tube to use root burls to make bowls.  Root burls have really interesting grain patterns but have a lot of cracks and craters.  My first root burl bowl turned out quite nice.

Scrub Oak Root Burl Bowl (unfinished)
Finding root burls without a lot of voids is hard, so I started filling the voids with epoxy resin.  It is messy but quite interesting and the results can be awesome!

Root Burl Bowl with clear epoxy inlay
Root Burl Bowl with colored epoxy inlay
Another with colored inlay
This one has gold mica epoxy inlay (My finest work so far)



A new table and a new hobby!

Sometime ago I convinced Elma Lynne to discard an old table we had in our apartment bedroom.  I did that by promising to make her a new one out of local black walnut.  I had cut down a couple of trees which I took and got milled  into lumber.  After it had dried for the requisite time I was out of excuses so I went to work on the table in January of 2018.

I cut several boards to about 48 inches in length, planed them to the desired thickness and glued them together then trimmed them to have a table top of about 39 inches square.  I had a log about 8 inches in diameter that I wanted to use for a pedestal, but I needed a fairly large lathe to mill it to size.  So I want to Harbor Freight and bought a lathe!

After a little practice I went to work on the log and turned a pretty nice pedestal, then made a base for it using some three inch thick walnut.  After a lot of sanding I put a urethane coat on it and finally presented it for Mother's Day.  It now holds a place of honor in the apartment bedroom, but I think it needs a couple of chairs.  Maybe that will be my next project, or at least a future project.

Black Walnut Table - pedestal view

Black Walnut Table - top view 
Oh, turning wood on a lathe has become my new hobby.  The reason the table took so long is that I had so much fun turning the pedestal that I started turning other stuff.  I made lamps, vases, goblets and bowls.  I watched You Tube a lot and got some neat ideas and had fun trying them out.  My main focus has become making bowls.  My next blog will be about my new hobby, turning bowls.

Thanksgiving 2018

We had most all of our family here for Thanksgiving this year.  The exceptions were Deedra who is completing her mission in Indiana and will be home on December 19th, and Nathan and his bride Lindsey who are with her family.

We put a turkey in the smoker around 6:00 pm Wednesday evening.  This is a new thing for us.  We often have bought smoked turkey before, but this is the first time we have smoked our own.

Joel and his family arrived around 8:00 pm, reporting that traffic was horrible!  We were watching a BYU basketball game and he was an hour late.  Jillyn and family arrived a couple of hours later, also victims of the traffic.  The timer popped so we got the turkey out of the smoker around 10:00 pm.  I used Mesquite wood chips because that was all I have.  If I do it again I think I will get some apple chips.  The mesquite smells a little too harsh for turkey, but it tastes fine.  The juices spilled onto the hot metal and created some more smoke which also affected the flavor some I think.

Thursday morning we made preparations for the big feast.  Another larger turkey was stuffed and put in the oven.  Darin, Clay and families arrived and we ate around 1:30 pm.  Everything was good.  Lori and Tiffany brought pies, Jillyn made rolls and Suzanne brought a good fruit salad.  Tiffany's mother joined us as she is all alone living in Hurricane.

Just before turkey.  Tiffany's mom Karen took photo.

After eating we all took a turn saying what we are thankful for, and we have so much!

Friday was kind of a casual day.   Clay, Ashlyn, Joel and Desiree got up early and went to Zion and hiked Angel's Landing. Suzanne and kids went Black Friday shopping, Jillyn and family went to a movie, some played games. and we had the annual turkey (clay pigeon) shoot.  I couldn't shoot because of my surgery, but it was fun watching the others, and taking photos.

Clay loading the thrower

Lori taking aim

Ashlyn popping a bird!
Darin and Joel figuring it out

Ashlyn loves to shoot

I left before it was finished so I could get ready for my Temple shift.  Later most of the grand kids and a few parents came to the temple and did baptisms for the dead.  It was fun to have them there.

Saturday  we had a talent show.  Most of the grand kids participated.  Some played the piano, some sang, Sydnee did a magic trick which amazed is all 😉.  Jillyn, Mckenna and Ella sang accompanied by Elma Lynne on the piano and Camille on the flute.  Camille is getting really good.  Brevin played the ukulele while Darin and Paxton sang.  Paxton has a good voice.  The adults played a few rounds of Scum while the children played in the basement, then starting at 4:00 pm some watched BYU basketball and football games while some of the women went to a movie.  Jillyn and family left to be home for Sunday responsibilities.

Sunday we got up and went to Sacrament meeting and then everyone changed clothes and headed home.  It was a great holiday and great to have our family around us.  It may be a while before we are able to have them all here again.